![]() ![]() If you think it's useful, hit the button below. Download For Homebrew user: brew install intellidock Configurable sensitivity. ![]() Adjust the distance at which the Dock starts to hide itself. Grid is a window manager that works well with IntelliDock. You need JavaScript enabled to view it. if no tension is felt on the RF plug.IntelliDOCK also supports the use of an optional compact Beam Privacy Handset ( Beam RST755I) that can be located next to the IntelliDOCK for added convenience if required. Contact This email address is being protected from spambots. If there is no tension felt, the plug may have come off the lock ring and therefore can no longer provided enough force to establish good contact between connectors. Do this 5 times to get a good feel of the tension. Gently push the RF plug with your pointer finger by 3mm and release. The RF plug is held in place by a lock ring and a spring. If there is still no signal reception proceed to the next step. First, follow the correct docking procedure "Inserting & Ejecting 9555 handset".If the correct procedure is not observed alignment issues may be expected and therefore poor or no satellite signal reception can be received. If this is not known it is recommended to check the integrity of the cable and antenna before proceeding to the steps below.Ī correct docking procedure is required to allow proper contact of the adapter and the 9555 rear connector. The 9555 Docking Station has an RF Adapter that plugs into the back of the Iridium 9555 handset to pass through the Iridium satellite signal from the external antenna.īefore proceeding, it must be determined first that the cable and antenna are in a known working condition. Other sources of RF interference such as Globalstar units, radar devices and broadcast stations can provide interference for Iridium units, but usually are not encountered as frequently as Inmarsat terminals.Īlso refer to “Assuring Quality of Iridium Service” in the Antenna Installation Guide. Generally speaking, an Iridium unit, be it a handset using its internal antenna or a fixed terminal when attached to an externally mounted antenna and located within 15 and 45 meters (50 to 150 feet, respectively) of an operating Inmarsat Standard-C terminal, will likely experience degraded performance. All Iridium units are susceptible to this interference, regardless of the type of antenna being used. The location of the Inmarsat unit’s antenna in relation to the Iridium unit’s antenna plays a significant role in determining the degree of signal degradation that an Iridium subscriber can expect to experience. Inmarsat terminals are often found in the same locations as Iridium subscribers, such as harbors, airports and especially onboard ships. The power with which Inmarsat units transmit can overpower the Iridium unit’s ability to properly maintain a quality connection with the Iridium satellite constellation. Some subscribers have contacted Iridium regarding the loss of signal quality when they operate their equipment near active Inmarsat terminals. It is important that certain considerations be taken into account for best performance when an Iridium/Inmarsat system is installed. This problem is especially evident when numerous antennas and broadcasting devices are located within close proximity to each other.Ī good example would be onboard a ship. Refer to the Beam Data Guide for more information.Īll wireless devices, including satellite telephones, are susceptible to RF (Radio Frequency) interference from other electronic devices. The “RING” string should be decipherable by the target device/program. ![]() * The baud rate can be set to whatever baud rate the device answering the call is going to need and not necessarily 19.2k. During the waiting period, the Data RX activity timeout can expire, and Voice calls can be made (Applies only to RST100 model, with serial numbers > 10001000). The device is now ready to answer an incoming data call automatically. ![]() AT+IPR=5 sets to 9600bps Terminal rate)ĪT&W0 (This stores the current (active) settings to Profile 0 of the RST100). Once connected, type the following AT commands:ĪT+IPR=x (where x baud of Terminal Program, according to ATS0=1 (This turns on auto-answer)ġ = 600 bps 2 = 1200 bps 3 = 2400 bps 4 = 4800 bps 5 = 9600 bps 6 = 19200 bps (default)Į.g. To initialise the Iridium data terminal to receive an incoming data call, start a Terminal Program (such as HyperTerminal) with the following settings: 19200* bps, 8, N, 1, Flow Control = None. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |